Application of Particle Swarm Optimization in Duty Cycle Adjustment for Optimization of Oxyhydrogen Generator

Fungky Dyan Pertiwi, Dhimas Cahyo Anindito, Ilham Habibi, Tri Vicca Kusumadewi, Muji Setiyo, Aditya Kolakoti

Abstract


The duty cycle of pulse width modulation is used to adjust the current of the oxyhydrogen generator with on-off square signals. These signals are essential for an oxyhydrogen gas generator to reduce thermal operation, improve the quality of oxyhydrogen gas, and enhance efficiency. A framework combining particle swarm optimization and regression analysis was proposed to determine the minimum temperature and production time of oxyhydrogen gas while maximizing efficiency using a single input, the duty cycle. The optimization results indicated that the duty cycle for the optimum solution remained within the upper and lower temperature boundaries. In this study, particle swarm optimization successfully provided valuable insights for practical applications in renewable energy technologies.

Keywords


Dry cell type; Duty cycle; HHO; Hydrogen generator; Regression analysis

Full Text:

PDF

References


Adedoja, O. S., Saleh, U. A., Alesinloye, A. R., Timiyo, T. E. J., Onuigbo, I. F., Adejuwon, O. O., and Josiah, E. (2023). An energy balance and multicriterial approach for the sizing of a hybrid renewable energy system with hydrogen storage. e-Prime-Advances in Electrical Engineering, Electronics and Energy, 4, 100146.

Ahmad, A., and Yadav, A. K. (2024). Parametric analysis of wastewater electrolysis for green hydrogen production: A combined RSM, genetic algorithm, and particle swarm optimization approach. International Journal of Hydrogen Energy, 59, 51-62.

Al-Rousan, A. A., and Sa'ed, A. (2018). Effect of anodes-cathodes inter-distances of HHO fuel cell on gasoline engine performance operating by a blend of HHO. International Journal of Hydrogen Energy, 43(41), 19213-19221.

Anggono, W. Stanley, S. P., Ronaldo, F., Gotama, G. J., Guo, B.,Yilmaz, E., Ichiyanagi, M., and Suzuki, T. (2021). Engine performances of lean iso-octane mixtures in a glow plug heated sub-chamber SI engine. Automotive Experiences, 5(1), 16–27.

Arini, R. N. and Kawano, D. S. (2012). Pengaruh variasi duty cycle pada pulse width modulation terhadap performa generator gas hho tipe basah (Wet Cell) 9 Plat SS 316L 10x10 mm. Jurnal Teknik Pomits, 1(1), pp. 1–5.

Ariyanto, S. R., Suprayitno, S., and Wulandari, R. (2023). Design of metallic catalytic converter using pareto optimization to improve engine performance and exhaust emissions. Automotive Experiences, 6(1), 200-2015.

Baltacıoğlu, M. K. (2019). A novel application of pulse width modulation technique on hydroxy gas production. International Journal of Hydrogen Energy, 44(20), 9726-9734.

Conker, Ç. (2019). A novel fuzzy logic based safe operation oriented control technique for driving HHO dry cell systems based on PWM duty cycle. International Journal of Hydrogen Energy, 44(20), 9718-9725.

Cui, Y., Geng, Z., Zhu, Q., and Han, Y. (2017). Multi-objective optimization methods and application in energy saving. Energy, 125, 681-704.

Duan, X., Xiao, J., Peng, X., Feng, S., Wang, S., and Wen, J. (2023). Multi-objective optimization of water electrolysis based on coupling model of electrochemistry and multiphase flow. Journal of Environmental Chemical Engineering, 11(6), 110985.

Elehinafe, F. B., Okedere, O. B., Ebong-Bassey, Q. E., and Sonibare, J. A. (2021). Data on emission factors of gaseous emissions from combustion of woody biomasses as potential fuels for firing thermal power plants in Nigeria. Mechanical Engineering for Society and Industry, 1(2), 78-85.

Elehinafe, F. B., Ezekiel, S. N., Okedere, O. B., and Odunlami, O. O. (2022). Cement industry–Associated emissions, environmental issues and measures for the control of the emissions. Mechanical Engineering for Society and Industry, 2(1), 17-25.

Ghiffari, Y. A., and Kawano, D. S. (2013). Tipe dry cell dan wet cell berdimensi 80 x 80 mm dengan penambahan PWM E-3 FF (1 kHz). Jurnal Teknik ITS, 2(2), B245-B250.

Hardiyanto, C., and Prawoto, P. (2023). Effect of diethyl ether on performance and exhaust gas emissions of heavy-duty diesel engines fueled with biodiesel-diesel blend (B35). Automotive Experiences, 6(3), 687-701.

Herlambang, Y. D., Sulistiyo, W., Margana, M., Apriandi, N., Marliyati, M., Setiyo, M., and Shyu, J. C. (2023). Application of a PEM fuel cell engine as a small-scale power generator for small cars with different fuel concentrations. Automotive Experiences, 6(2), 273-289.

Herlambang, Y.D., Sulistiyo, W., Margana, M., Apriandi, N., Nursaputro, S.T., Marliyati, M., Setiyo, M., Purwanto, W., Rochman, M.L. and Shyu, J.C. (2024). Study on solar powered electric vehicle with thermal management systems on the electrical device performance. Automotive Experiences, 7(1), 18-27.

Jalili, M., Chitsaz, A., Holagh, S. G., Ziyaei, M., and Rosen, M. A. (2021). Syngas-fed membrane-based and steam and water-fed electrolysis-based hydrogen production systems: renewability, sustainability, environmental and economic analyses and optimization. Journal of Cleaner Production, 326, 129424.

El Kady, M. A., Farrag, A. E. F., Gad, M. S., El Soly, A. K., and Hashish, H. A. (2020). Parametric study and experimental investigation of hydroxy (HHO) production using dry cell. Fuel, 282, 118825.

Kivevele, T., Raja, T., Pirouzfar, V., Waluyo, B., and Setiyo, M. (2020). LPG-fueled vehicles: An overview of technology and market trend. Automotive Experiences, 3(1), 6-19.

Krekel, D., Samsun, R. C., Peters, R., and Stolten, D. (2018). The separation of CO2 from ambient air–A techno-economic assessment. Applied Energy, 218, 361-381.

Kumar, S. S., and Kumar, K. S. (2015). Optimization and control of fuel by producing brown gas by HHO generating device controlled by VHDL and implementing in FPGA. International Journal of Mechanical Engineering and Robotics Research, 4(1), 154-162.

Maghfiroh, H., Wahyunggoro, O., and Cahyadi, A. I. (2023). Low pass filter as energy management for hybrid energy storage of electric vehicle: A survey. Automotive Experiences, 6(3), 466-484.

Marini, F., and Walczak, B. (2015). Particle swarm optimization (PSO). A tutorial. Chemometrics and Intelligent Laboratory Systems, 149, 153-165.

Mohammed, A. T., Said, M. F. M., Othman, N., Opia, A. C., and Veza, I. (2023). Feasibility study of biofuel incorporated nanoparticles as sustainable IC engine fuel: Opportunities and challenges-an overview. Automotive Experiences, 6(1), 94-121.

Mukherjee, S. S., Meshram, H. A., Rakshit, D., and Saha, B. B. (2023). A comparative study of sensible energy storage and hydrogen energy storage apropos to a concentrated solar thermal power plant. Journal of Energy Storage, 61, 106629.

Munahar, S., Setiyo, M., Brieghtera, R. A., Saudi, M. M., Ahmad, A., and Yuvenda, D. (2023). Fuel control system on cng fueled vehicles using machine learning: A case study on the downhill. Automotive Experiences, 6(1), 173–187.

Munahar, S., Purnomo, B. C., and Köten, H. (2021). Fuel control systems for planetary transmission vehicles: A contribution to the LPG-fueled vehicles community. Mechanical Engineering for Society and Industry, 1(1), 14-21.

Munusamy, T. D., Chin, S. Y., and Khan, M. M. R. (2022). Optimization of process parameters for photoreforming of hydrogen evolution via response surface methodology (RSM): A study using Carbon@ exfoliated g–C3N4. Chemical Engineering Research and Design, 177, 513-525.

Özgür, T., and Yakaryilmaz, A. C. (2018). Thermodynamic analysis of a proton exchange membrane fuel cell. International Journal of Hydrogen Energy, 43(38), 18007-18013.

Pertiwi, F. D., and Kawano, D. S. (2013). Pengaruh penambahan PWM (Pulse Width Modulation) pada generator HHO Tipe Dry Cell. Jurnal Teknik ITS, 2(2), B339-B344.

Pham, T. H., Lee, B. K., Kim, J., and Lee, C. H. (2016). Enhancement of CO2 capture by using synthesized nano-zeolite. Journal of the Taiwan Institute of Chemical Engineers, 64, 220-226.

Pradipta, B. A., and Kawano, D. S. (2013). Studi eksperimen pengaruh pencampuran gas hidrogen dari generator hho tipe kering dengan bahan bakar kerosene pada distribusi temperatur nyala api kompor tekan blowtorch. Jurnal Teknik ITS, 2(2), B305-B309.

Raja, T., Setiyo, M., Murugan, V., and Dhandapani, S. (2023). Analysis of the temperature variation of bizarre thermal barrier coatings and their impacts on engine. Automotive Experiences, 6(3), 497-514.

Ramadhani, F., Hussain, M. A., Mokhlis, H., and Hajimolana, S. (2017). Optimization strategies for Solid Oxide Fuel Cell (SOFC) application: A literature survey. Renewable and Sustainable Energy Reviews, 76, 460-484.

Rezk, H., Ferahtia, S., Djeroui, A., Chouder, A., Houari, A., Machmoum, M., and Abdelkareem, M. A. (2022). Optimal parameter estimation strategy of PEM fuel cell using gradient-based optimizer. Energy, 239, 122096.

Rocha, F., de Radiguès, Q., Thunis, G., and Proost, J. (2021). Pulsed water electrolysis: A review. Electrochimica Acta, 377, 138052.

Santos, D. M., Sequeira, C. A., and Figueiredo, J. L. (2013). Hydrogen production by alkaline water electrolysis. Química Nova, 36, 1176-1193.

Santoso, B., Sartomo, A., Ubaidillah, U., Muraza, O., and Maharani, E. T. (2024). The impact of varying mixing rates in a surfactant-free fuel emulsion mixer on the efficiency and emissions of a diesel engine. Automotive Experiences, 7(1), 132-148.

Secer, A., and Hasanoğlu, A. (2020). Evaluation of the effects of process parameters on co–gasification of Çan lignite and sorghum biomass with response surface methodology: An optimization study for high yield hydrogen production. Fuel, 259, 116230.

Setiawan, I. C., and Setiyo, M. (2024). Fueling the future: The case for heavy-duty fuel cell electric vehicles in sustainable transportation. Automotive Experiences, 7(1), 1-5.

Sharma, P., Sahoo, B.B., Said, Z., Hadiyanto, H., Nguyen, X.P., Nižetić, S., Huang, Z., Hoang, A.T. and Li, C. (2023). Application of machine learning and Box-Behnken design in optimizing engine characteristics operated with a dual-fuel mode of algal biodiesel and waste-derived biogas. International Journal of Hydrogen Energy, 48(18), 6738-6760.

Silaen, C., and Kawano, D. S. (2014). Optimalisasi generator gas HHO tipe wet cell dimensi 160x160 mm dan 120x120 mm dengan penambahan digital pulse width modulation dan netral plat. Jurnal Teknik POMITS, 1(1), 1–9.

Subramanian, B., and Thangavel, V. (2020). Analysis of onsite HHO gas generation system. International Journal of Hydrogen Energy, 45(28), 14218-14231.

Sudarmanta, B., Darsopuspito, S., and Sungkono, D. (2016). Application of dry cell HHO gas generator with pulse width modulation on sinjai spark ignition engine performance. International Journal of Research in Engineering and Technology, 5(2), 105-112.

Tambunan, B. H., Ambarita, H., Sitorus, T. B., Sebayang, A. H., and Masudie, A. (2023). An overview of physicochemical properties and engine performance using rubber seed biodiesel–plastic pyrolysis oil blends in diesel engines. Automotive Experiences, 6(3), 551-583.

Veza, I., Setiawan, I.C., La Ode, M.F., Handi, H., Amanah, A., Kurnia, M.T., Paristiawan, P.A., Idris, M., Sule, A. and Opia, A.C. (2023). Strategies to achieve controlled auto-ignition (CAI) combustion: A review. Mechanical Engineering for Society and Industry, 3(1), 22-34.

Waluyo, B., Pujiarto, B., Ardana, N., Rochman, M. L., and Adi, A. T. (2023). Optimizing energy harvesting from waste motor oil through steam reforming: A path to efficient combustion and emissions reduction. Mechanical Engineering for Society and Industry, 3(2), 86-92.

Wilberforce, T., Rezk, H., Olabi, A. G., Epelle, E. I., and Abdelkareem, M. A. (2023). Comparative analysis on parametric estimation of a PEM fuel cell using metaheuristics algorithms. Energy, 262, 125530.

Worawat, S. N., and Aurasopon, A. (2015). Application of microcontroller for controlling HHO dry cell in small trucks. Engineering Access, 1(2), 10-13.

Yahya, H. S. M., Abbas, T., and Amin, N. A. S. (2021). Optimization of hydrogen production via toluene steam reforming over Ni–Co supported modified-activated carbon using ANN coupled GA and RSM. International Journal of Hydrogen Energy, 46(48), 24632-24651.

Yamamoto, H., Fujioka, H., and Okano, K. (2021). Cost analysis of stable electric and hydrogen energy supplies derived from 100% variable renewable resources systems. Renewable Energy, 178, 1165-1173.

Yilmaz, A. C., Uludamar, E., and Aydin, K. (2010). Effect of hydroxy (HHO) gas addition on performance and exhaust emissions in compression ignition engines. international journal of hydrogen energy, 35(20), 11366-11372.

Zhang, G., Yan, Z., Liu, Q., and Lu, G. (2024). Multi-objective optimization strategy for multipolar magnesium electrolysis cell based on thermal-electric model. Chemical Engineering Journal, 490, 151690.




DOI: https://doi.org/10.17509/ajse.v4i2.70509

Refbacks

  • There are currently no refbacks.


Copyright (c) 2024 Universitas Pendidikan Indonesia

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

ASEAN Journal of Science and Engineering (AJSE) is published by UPI 

View My Stats